Catalina - Capri - 25s International Assocaition Logo(2006)  
Assn Members Area · Join
h.jpg Home.
a.jpg Association Forum
s.jpg Ships Store
c.jpg Cruising
r.jpg Racing
t.jpg Technical Tips
g.jpg Photo Gallery - New
o.jpg Boat Search - Updated
m.jpg Manuals & Brochures
3rdrpt.jpg Swap Meet
l.jpg Links
f.jpg Officer Flag Line & Staff
b.jpg Bylaws & Constitution
 
1.jpg Members Area
1.jpg Join the Association
 
Notice:
The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.
 
Association Forum
Association Forum
Home | Profile | Register | Active Topics | Forum Users | Search | FAQ
Username:
 Password:
Save Password
Forgot your Password?

 All Forums
 Catalina/Capri 25/250 Sailor's Forums
 Catalina 25 Specific Forum
 Rudder Gudgeons		  New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

delling3
Deckhand

Member Avatar

USA
13 Posts
Initially Posted - 04/06/2022 :  10:19:01  Show Profile  Reply with Quote
Tried searching for this, but didn't find anything. I am sure it's been covered before. I am replacing the gudgeons on my '85 C-25. Does anyone know when Catalina switched over to a glassed in threaded mounting plate, as opposed to nuts and backing washers? I would prefer not to have to cut an access port to change out the fastners!

Thanks in advance.

islander
Master Marine Consultant

Members Avatar

USA
3992 Posts
Response Posted - 04/06/2022 :  11:10:17  Show Profile  Reply with Quote
If your talking about that bronze plate that the screws threaded into I dont remember mine being glassed in. I think they were just barely held there by some caulk. Those plates aren't very thick and only have a few threads in them so putting washers and Nylock nuts over the plates is a good idea. You can check what your boat has by removing the teak access panel at the back of the berth. you can see/feel the lowerer plate and nuts if any there. You only need to cut an access hole for the upper gudgeon.
Scott-"IMPULSE"87'C25/SR/WK/Din.#5688
Sailing out of Glen Cove,L.I Sound


Go to Top of Page

waterbaby
Navigator

Members Avatar

USA
168 Posts
Response Posted - 04/06/2022 :  11:32:34  Show Profile  Reply with Quote
Hey Scott, that's a great picture! Can you tell me how much space do you have to work with between the liner and the hull? In you picture it looks like there's almost no space at all.
1986 TR/SK #5250 Sunshine
Go to Top of Page

islander
Master Marine Consultant

Members Avatar

USA
3992 Posts
Response Posted - 04/06/2022 :  17:36:21  Show Profile  Reply with Quote
I would guess that it was @ 3-4". Look how wide the transom is where the tiller crosses over it. That can give you an idea. If you look closely at the photo you will see that I had to cut a notch in the inspection port flange to clear the bronze plate and the two outside bolts/nuts.
Scott-"IMPULSE"87'C25/SR/WK/Din.#5688
Sailing out of Glen Cove,L.I Sound


Edited by - islander on 04/06/2022 17:47:25
Go to Top of Page

Stinkpotter
Master Marine Consultant

Members Avatar

Djibouti
9013 Posts
Response Posted - 04/06/2022 :  19:49:26  Show Profile  Reply with Quote
The '85 looks just like Scott's photo. Nuts are a good idea--washers optional, since the plate acts like one.
Dave Bristle
Association "Port Captain" for Mystic/Stonington CT
PO of 1985 C-25 SR/FK #5032 Passage, USCG "sixpack" (expired),
Now on Eastern 27 $+!nkp*+ Sarge
Go to Top of Page

delling3
Deckhand

Members Avatar

USA
13 Posts
Response Posted - 04/07/2022 :  06:36:10  Show Profile  Reply with Quote
Great help, thanks. Appears I need to get an access port. I would like to make this hole as small as practical. Any opinions on what diameter to use. CD has one with a 4" opening - that seems larger than necessary?

Thanks again!
Go to Top of Page

islander
Master Marine Consultant

Members Avatar

USA
3992 Posts
Response Posted - 04/07/2022 :  07:02:27  Show Profile  Reply with Quote
I also wanted the hole as small as possible so I used a 3" deck plate. The one in the photo is this one. You will have to trim it a bit as I said above.
https://www.amazon.com/Nicro-N10863DW-plate-white-snap/dp/B000NI01VC
Scott-"IMPULSE"87'C25/SR/WK/Din.#5688
Sailing out of Glen Cove,L.I Sound


Go to Top of Page

Voyager
Master Marine Consultant

Members Avatar

USA
5231 Posts
Response Posted - 04/07/2022 :  10:35:14  Show Profile  Reply with Quote
Several years back, whilst on a passage, my gudgeons loosened up and I almost lost the lower one in the drink! So I reinstalled new SS bolts in the bottom one down below in the quarterberth access panel using flat washers plus split washers and some locktite to keep them in place. Nylock nuts would have worked also.
I was similarly concerned about the top gudgeon, however, when checked it was snug as a bug in a rug. Nonetheless, I removed the bolts which looked fine. I applied some locktite on these too and screwed them back in finger-tight plus 1/2 a turn. Lo, these many years later, they’re all still fine and in place.
Also since then, each spring I walk around the boat with my screwdriver/nutdriver gun set on 3 and check any screws or bolts that I see. I generally find something that’s loose.
Bruce Ross
Passage ~ SR-FK ~ C25 #5032

Port Captain — Milford, CT
Edited by - Voyager on 04/07/2022 19:36:25
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
Association Forum © since 1999 Catalina Capri 25s International Association Go To Top Of Page
Powered By: Snitz Forums 2000 Version 3.4.06
Notice: The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.