Catalina - Capri - 25s International Assocaition Logo(2006)  
Assn Members Area · Join
h.jpg Home.
a.jpg Association Forum
s.jpg Ships Store
c.jpg Cruising
r.jpg Racing
t.jpg Technical Tips
g.jpg Photo Gallery - New
o.jpg Boat Search - Updated
m.jpg Manuals & Brochures
3rdrpt.jpg Swap Meet
l.jpg Links
f.jpg Officer Flag Line & Staff
b.jpg Bylaws & Constitution
 
1.jpg Members Area
1.jpg Join the Association
 
Notice:
The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.
 
Association Forum
Association Forum
Home | Profile | Register | Active Topics | Forum Users | Search | FAQ
Username:
 Password:
Save Password
Forgot your Password?

 All Forums
 Catalina/Capri 25/250 Sailor's Forums
 Catalina 250 Specific Forum
 Hull No. 922 - Closing Gap in Hatch		  New Topic  Topic Locked
 Printer Friendly
Author Previous Topic Topic Next Topic  

Carl in LA
Captain

Member Avatar

USA
284 Posts
Initially Posted - 05/19/2018 :  15:06:25  Show Profile
Any tips on closing the gap between panels in the hatch?

All the best,

Carl
Catalina 250 - Pretty Good Boat

Ellen254
Deckhand

Members Avatar

USA
12 Posts
Response Posted - 02/10/2019 :  15:41:04  Show Profile
Anyone have any thoughts on this? We've been having a good bit of rain lately, and I realized today that the gaps here are the source of the water that's getting in.
2004 C250WK #750 Waco, TX
"Ba-de-ya"
Go to Top of Page

Steve Milby
Past Commodore

Members Avatar

USA
5883 Posts
Response Posted - 02/10/2019 :  16:24:48  Show Profile
If you have a pop top enclosure, then the enclosure should cover the gaps at the upper corners of the hatch.

I had a similar problem with my C25. It also had little gaps at the upper corners of the hatch, and mud daubers got inside while I was away from the boat. I made a trapezoid shaped Sunbrella cover that covered the entire hatch. I left an extra flap of fabric, 5-6" long across the top. My boat had snaps set in the frame of the hatch on each side. I installed snaps in the cover. Then I snapped it over the hatch, and dropped the extra flap of fabric over the top of the hatchboards. Then I pulled the hatch shut. The cover kept out the mud daubers and water. Perhaps that will work on a C250.
Steve Milby J/24 "Captiva Wind"
previously C&C 35, Cal 25, C25 TR/FK, C22
Past Commodore
Go to Top of Page

dubedoo
1st Mate

Members Avatar

68 Posts
Response Posted - 02/12/2019 :  07:47:33  Show Profile
I don't have any ideas on closing the gap but Catalina Direct has a canvas "companion way cover" that snaps on around the companionway similar to how/where a pop top enclosure would snap. In fact it seemed to me that one came with my boat new in 2003 with the "canvas" package. Sure enough, just found it in storage in the garage with the pop top. Have never used either but haven't had a problem with rain getting in. The boat is in a slip all summer and in storage otherwise.
A companion way cover might not be practical other than when the boat is not in use but I do see quite a few of the boats in the local marina that have one snapped on when the owner leaves. Others just secure a tarp tent over the boom covering the companionway.

Steve
C250 wb #702
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Topic Locked
 Printer Friendly
Jump To:
Association Forum © since 1999 Catalina Capri 25s International Association Go To Top Of Page
Powered By: Snitz Forums 2000 Version 3.4.06
Notice: The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.