Association Forum

Assn Members Area · Join

Home.

Association Forum

Ships Store

Cruising

Racing

Technical Tips

Photo Gallery - New

Boat Search - Updated

Manuals & Brochures

Swap Meet

Links

Officer Flag Line & Staff

Bylaws & Constitution

Members Area

Join the Association

Notice:
The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.

Association Forum

All Forums

Catalina/Capri 25/250 Sailor's Forums

Catalina 25 Specific Forum

Heat and Hot Water

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:

UserName:

Password:

Format Mode:

Format:

Message:

* HTML is OFF
* Forum Code is ON

Smilies

Check here to include your profile signature.
Check here to subscribe to this topic.

T O P I C R E V I E W
bjoye	Posted - 07/02/2022 : 09:20:39 Not a project for the faint at heart. After oscillating back and forth for a year of so, I finally bit the bullet and installed an ESPAR hydronic diesel heating system. Since the boat is now in Boston, it can get really cold on the water, even in late summer, and I really hate being cold. There are a number of cheaper choices for heat and hot water, but, in terms of reliability and safety, I found the ESPAR diesel heater to be the best choice for me. (your milage may vary) If you are not familiar with ESPAR, it is German company that builds super reliable diesel boilers for preheating diesel truck engines in cold environs. They are usually mounted outside the cab, and can take the salt, dirt, and abuse of the highways. The kit consists of the boiler, a pump to circulate a glycol mixture, a fuel pump, controller, and wiring harness. I also purchased an 5KBTU air handler for hot air heat in the cabin and a heat exchanger for domestic hot water. I also purchased the 'Marine' kit , which consist of ABYC approved diesel fuel lines, exhaust hose with built in muffler, and exhaust thru-hull. I purchased my kit off of Amazon. The air handler, heat exchanger, 'Marine' kit all came from an outfit in the UK. I installed the boiler, diesel day tank, glycol header tank, pumps and electronics in the cockpit dumpster. All combustion takes place outside of the cabin in the dumpster. I measured the run time temperature of the boiler at 100 deg (you can touch it), and the highest temperature on the exhaust port at 140 deg. The actual exhaust hose is double walled and remains at ambient temperature. The glycol loop, enters the cabin, goes thru the heat exchanger for hot water under the galley and then to the air handler located in the storage area under the port settee, for hot air where the hot air exits thru a grill into the cabin at floor level The exhaust from the boiler exits the back of the boat at the stern thru a special thru-hull The diesel day tank holds 2+ quarts and should last the season. To control the boiler, it is one button push to fire up, which will run the boiler to maintain 165 deg in the glycol loop for 30 mins. You can extend or stop at anytime. It takes about a minute to fire up and another minute to bring the glycol loop up to temperature. The glycol pump requires around 5A and the air handler, 2A. In general, no smoke, no diesel smells, even in the closed dumpster. Hot air heat is controlled by a separate controller, which can be set to manual or automatic, and varies the blower motor speed based on heat demand. A few notes about installation: keep the glycol loop simple, the pump is not that strong, and any air trapped will prevent circulation. The ability to bleed the loop easily is important. In addition, have a CO detector in the cabin. (You should have one anyways, if you have any combustion taking place on the boat, including your outboard). Also, as all the instructions are in German, I found a number of Youtube videos of ESPAR installations for Van conversions, which helped a lot.
1 L A T E S T R E P L I E S (Newest First)
keats	Posted - 07/04/2022 : 11:42:17 Pretty impressive and well executed project. This should go in the magazine.

Association Forum

Notice: The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.