Catalina - Capri - 25s International Assocaition Logo(2006)  
Assn Members Area · Join
h.jpg Home.
a.jpg Association Forum
s.jpg Ships Store
c.jpg Cruising
r.jpg Racing
t.jpg Technical Tips
g.jpg Photo Gallery - New
o.jpg Boat Search - Updated
m.jpg Manuals & Brochures
3rdrpt.jpg Swap Meet
l.jpg Links
f.jpg Officer Flag Line & Staff
b.jpg Bylaws & Constitution
 
1.jpg Members Area
1.jpg Join the Association
 
Notice:
The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.
 
Association Forum
Association Forum
Home | Profile | Register | Active Topics | Forum Users | Search | FAQ
 All Forums
 Catalina/Capri 25/250 Sailor's Forums
 Catalina 250 Specific Forum
 centerboard bracket bolts, one lost one loose [:0]

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:
UserName:
Password:
Format Mode:
Format: BoldItalicizedUnderlineStrikethrough Align LeftCenteredAlign Right Horizontal Rule Insert HyperlinkInsert EmailInsert Image Insert CodeInsert QuoteInsert List
   
Message:

* HTML is OFF
* Forum Code is ON
Smilies
Smile [:)] Big Smile [:D] Cool [8D] Blush [:I]
Tongue [:P] Evil [):] Wink [;)] Clown [:o)]
Black Eye [B)] Eight Ball [8] Frown [:(] Shy [8)]
Shocked [:0] Angry [:(!] Dead [xx(] Sleepy [|)]
Kisses [:X] Approve [^] Disapprove [V] Question [?]

 
Check here to subscribe to this topic.
   

T O P I C    R E V I E W
SeaHunter Posted - 11/11/2024 : 06:55:26
Hello Sailors

Buying a 2005 250 WB/CB

Did a scuba inspection to fix CB lifting line and to my surprise I found the port side CB shaft bracket hanging low, one bolt missing and the other about to fall out.

I hand tightened the loose bolt.

I was really hoping someone could tell me the size of those bolts so I could install the missing one and tighten them (is there a torq spec?) to prevent losing the CB...

VECTRAN line on order, used a nylon rope to pull up board so I can load on trailer (haven't seen the trailer yet) to clean and possibly paint bottom.

Is it possible to lower CB any when on trailer to install vectran line or will I need to do that underwater?

I will also remove (if not stuck) the bolts and replace all four and install the loctite to prevent backing out and seizure.
8   L A T E S T    R E P L I E S    (Newest First)
Voyager Posted - 11/16/2024 : 07:11:30
Seahunter, after I posted, I realized you were probably an experienced diver with lots of hours on the water. Here in CT we lose about 10-20 people to hypothermia each year for a variety of reasons, mainly inexperience or stupidity.
SeaHunter Posted - 11/16/2024 : 06:48:46
I reviewed the bushing repair before I got the boat and that made me feel comfortable that if a problem it could be fixed.

Been diving since 1980 and an Easter egg hunt in a quarry in PA made me decide to move south #128518;

Cold is realtive and our winter water in SC is warm realtive to your water in CT probably year round #128518; Thanks for your advice and caring #128077;
k3fuller Posted - 11/14/2024 : 15:24:46
If your bushing is bad, take a look at my fix article that Russ made sticky. A bit time consuming but not necessarily hard. My bolts are probably original. When I bought the boat, one was backed part way out. I took them all out, cleaned them up and did the same as you are planning. Never had another problem. :- )
Voyager Posted - 11/14/2024 : 07:18:34
Watch for signs of hypothermia as you work in cold water, take frequent breaks to warm yourself back up. Allow yourself some time to warm up gradually during breaks. Wear a wetsuit.
As hypothermia begins to set in, you will notice that your hands and fingers will slow down, and you’ll fumble with parts and tools. That’s a sure sign.
Take care of yourself first, the boat can wait.
SeaHunter Posted - 11/14/2024 : 06:45:26
Thanks for the info.

Here is a follow-up for future 250 owners

I've installed four Hex head 3/8-16 x 1 1/4 304 stainless bolts with locktite blue and will make this an annual maintenance item. I will be removing CB to checkout the bushing.

I ordered 5500lb vectran from West coast sailing. 5mm Samson Validator 12 Vectran Lin https://westcoastsailing.net/5mm-samson-validator-12-vectran-line/

My boat was already setup with the lifting tackle so following the diagram it literally uses bowlines to attach the vectran. The water is cooling fast so I'll get that lifting line inplace asap.

https://www.catalinadirect.com/c-250-centerboard-lifting-tackle-pdf/
Little Wind Posted - 11/13/2024 : 09:55:10
Both my keel hangers fell off while in my slip. I can tell that they were not installed correctly. See these links from Catalina Direct https://www.catalinadirect.com/shop-by-boat/catalina-250/hull-deck/keel/keel-hanger-casting-kit-c-25-c-250/ and https://www.catalinadirect.com/shop-by-boat/catalina-25/hull-deck/keel/pivot-assy/keel-fastener-kit-for-c-25-c-250/
This would probably require a haul-out and jack pads.

Also, I don't know where you are getting your VECTRAN from but this kit is available if you need it. https://www.catalinadirect.com/shop-by-boat/catalina-250/hull-deck/keel/c-250-keel-lifting-pennant-retrofit-assy/

Good luck.
SeaHunter Posted - 11/13/2024 : 08:26:33
Hex head 3/8-16 x 11/4

Bolts were easy on trailer

Up-haul impossible on trailer.

Thanks
zeil Posted - 11/11/2024 : 13:29:16
It's easy to do while in the water and (nearly) impossible on the trailer. Vectran 5 mm up-haul works best.

No idea what thread or bolt size that would be. Please describe which bolt is missing. A photo would be better. The center board mounting brackets are bolted with 4 bolts if I'm not mistaken


Association Forum © since 1999 Catalina Capri 25s International Association Go To Top Of Page
Powered By: Snitz Forums 2000 Version 3.4.06
Notice: The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.