Notice:
The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.
Note: You must be registered in order to post a reply. To register, click here. Registration is FREE!
T O P I C R E V I E W
islander
Posted - 04/27/2019 : 12:30:04 Well I finally got around to replacing my shabby transom trim. CD says that it is a trim to fit part. Not a problem until I lined it up on the transom. You would think that it would be close with enough material to trim down. Nope. As you can see the part that is suppose to cover the rub rail end cap is not wide enough nor does it line up with the end cap. The only choice is to cut it off entirely and is what I ended up doing. It still looks better than my crumbling original. Anybody else replace this trim? If so how did it work for you?
Nasty old trim
End cap cover too small and mismatch
End result
10 L A T E S T R E P L I E S (Newest First)
bigelowp
Posted - 05/03/2019 : 07:45:23 I replaced the rim when I got Limerick in 06 the trim still looks pretty good, but was thinking of replacing with the "new and improved" UV resistant version as Scott has done so well.
pastmember
Posted - 05/03/2019 : 07:35:14 I tossed my old one and never looked back.
islander
Posted - 04/30/2019 : 07:34:51 Worth it to make the stern look good.
Exactly, It's the view the competition will see, Right?
Voyager
Posted - 04/29/2019 : 14:53:20 I was thinking that I could just paint it up with some GelCoat or two-part Polyurethane paint. The $43 trim piece is a heckova lot easier and less costly in the long run.
Peregrine
Posted - 04/29/2019 : 13:43:11 Nice job trimming it. I replaced mine ages ago and the new piece didn't have the molded bump outs but was too long. A post on the forum advised just trimming it and it has been fine for years. I guess all replacements will need trimming. Worth it to make the stern look good.
OLarryR
Posted - 04/29/2019 : 03:24:29 Scott - Despite the fit issues, you did a great job trimming it to fit. Great job !
islander
Posted - 04/28/2019 : 11:36:30 Ah Ha, Bruce Dave just solved you mystery.
Stinkpotter
Posted - 04/28/2019 : 11:28:09
quote:Originally posted by Voyager
...Thinking about that detail on Passage I’m not 100% sure that there is a cover on mine. And right there the gel coat is a little thin in spots...
That's because I removed the frame and filled the holes--the vinyl was badly deteriorated and Passage looked better without it. I didn't buy CD's because at that time they were the same thin vinyl (?) as the originals. I couldn't justify a thin piece of Starboard big enough to make a one-piece frame that would fit under the rudder (now about $42).
islander
Posted - 04/28/2019 : 11:16:43 Here's the link for the transom trim. After reading the description again I answered my own question. It states that the trim was also used on the 22 and the cups fit them. On the 25 you cut them off. My bad.https://www.catalinadirect.com/shop-by-boat/capri-22/hull-deck/stern/transom-trimimproved-uv-resistant/ Bruce, Possible yours is just missing having disintegrated before you got the boat.
Voyager
Posted - 04/28/2019 : 10:49:45 Wow Scott, nice upgrade!! While the piece didn’t exactly fit, you made the most out of it. Thinking about that detail on Passage I’m not 100% sure that there is a cover on mine. And right there the gel coat is a little thin in spots. I was never certain what the solution was to improving the look. Kindly share the link from CD.
Notice: The advice given on this site is based upon individual or quoted experience, yours may differ. The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.