Association Forum

Assn Members Area · Join

Home.

Association Forum

Ships Store

Cruising

Racing

Technical Tips

Photo Gallery - New

Boat Search - Updated

Manuals & Brochures

Swap Meet

Links

Officer Flag Line & Staff

Bylaws & Constitution

Members Area

Join the Association

Notice:
The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.

Association Forum

All Forums

Catalina/Capri 25/250 Sailor's Forums

Catalina 250 Specific Forum

Water supply for "Mariah"

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:

UserName:

Password:

Format Mode:

Format:

Message:

* HTML is OFF
* Forum Code is ON

Smilies

Check here to include your profile signature.
Check here to subscribe to this topic.

T O P I C R E V I E W
zeil	Posted - 06/03/2020 : 21:47:35 We've removed the 20 gallon water tank on Mariah from below the V Berth to a new 10 gallon tank located behind the wet locker. A new water inlet hole needed to be drilled in the hull on the port side to line up with the aft leg of the midship's stanchion inspection port. New water supply lines run from the tank via a 12V pump located in the wet locker below the sole to a tap in the galley and a hand pump located in the head. Before marking and drilling Took the plunge and drilled a 1 3/4" hole Looking in the hole and through the inspection port into the bilge opening Below the wet locker side panel often you'll find wetness causing the wood to soak up moisture and rot. In order to avoid this I've shortened the new panel by 1/2 inch and replaced with a strip of 1/2" breadboard type of material (sorry I don't know the name of the material)
6 L A T E S T R E P L I E S (Newest First)
zeil	Posted - 06/16/2020 : 21:26:57 On our previous 1995 C250WB a factory installed 10 gallon water tank was placed in exactly the same location. We used an 8HP long shaft Honda with manual start. The boat was dead on its lines and remained so even though, at one time, we outfitted and provisioned the boat for living aboard for over a year. We also enjoyed month or longer cruises with different gear not causing noticeable changes Often additional water supply was stored in the V Berth in the form of standard packs of store bought water bottles but with or without we never noticed much or any difference. It seems that the WB as opposed to WK models may have an advantage when considering waterline and other behavioral issues. Our new to us '96WB "Mariah" was equipped with a 20 gallon horizontal tank located in the V berth with a fill cap located on the counter awkwardly behind the stove top. Perhaps due to winterizing, poor ventilation, usage, tank draining problems including the lines affected the water supply. Besides taking up valuable storage space while hard to observe hard when filling the tank. For those reasons we removed the old tank and opted for a smaller, out of the way, ventilated and easy to see when filling the tank from outside the boat.
kjk	Posted - 06/15/2020 : 17:50:51 Does that affect the balance? I have added flexible water tanks for ballast in the area below the V berth to compensate for the engine's weight (and mine)
zeil	Posted - 06/09/2020 : 09:00:39 Wayne I routed the electrical wires of the pump through a drilled hole from the wet locker to the bilge and below the sole to the galley cupboard where they are connected to the tap via a small sub-panel together with the stove and butane gas sniffer alarm as well. The beauty of this pump is that it provides water on demand without pressurized waterlines and allows the hand pump in the head to work
zeil	Posted - 06/08/2020 : 22:06:30 Wayne Cutting holes on the side of the hull is scary business but... it turned out to be in the right place Dave The half round panel is the new replacement panel to fit the stern battery compartment bulkhead which needed an additional slight adjustment before fitting properly. The old piping on this panel was still "like new", and could be reused after a good wash . The smaller other panel fits the aft berth port side coaming. In all cases I've used the old panels as templates including the screw hole locations Catalina designed, fabricated and fitted the individual panels without disturbing or having to remove most others... Access panel to battery compartment
Stinkpotter	Posted - 06/07/2020 : 20:05:15 I'm mystified... What't this??
wm36	Posted - 06/07/2020 : 19:25:41 You're a brave man Henk to take a hole saw to your boat. Glad it worked out well for you. Question: how will you run the wires for the pump?

Association Forum

Notice: The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.