Catalina - Capri - 25s International Assocaition Logo(2006)  
Assn Members Area · Join
Association Forum
Association Forum
Home | Profile | Register | Active Topics | Forum Users | Search | FAQ
 All Forums
 Catalina/Capri 25/250 Sailor's Forums
 Catalina 250 Specific Forum
 Clew Reefing

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:
UserName:
Password:
Format Mode:
Format: BoldItalicizedUnderlineStrikethrough Align LeftCenteredAlign Right Horizontal Rule Insert HyperlinkInsert EmailInsert Image Insert CodeInsert QuoteInsert List
   
Message:

* HTML is OFF
* Forum Code is ON
Smilies
Smile [:)] Big Smile [:D] Cool [8D] Blush [:I]
Tongue [:P] Evil [):] Wink [;)] Clown [:o)]
Black Eye [B)] Eight Ball [8] Frown [:(] Shy [8)]
Shocked [:0] Angry [:(!] Dead [xx(] Sleepy [|)]
Kisses [:X] Approve [^] Disapprove [V] Question [?]

 
Check here to subscribe to this topic.
   

T O P I C    R E V I E W
doublereefed Posted - 09/16/2019 : 13:41:59
I have single line reefing, I think it was standard. Total PITA, never works, too much friction, too many points to get tangled up. I think I'll go with using the current setup for just the tack, and then set up a line as shown below for the clew.

I'm thinking I will use a turning block (cheek block?), and then a cam cleat at the mast towards the tack.

What are best practices here, good solutions that are out there?

Thanks...





3   L A T E S T    R E P L I E S    (Newest First)
TakeFive Posted - 09/17/2019 : 17:17:34
quote:
Originally posted by doublereefed

Thanks for that Take Five. Hadn't though about the line needing to go to the end of the boom. I will figure that out.

How is the block attached to the cringle? I Googled and couldn't find any photos to show me how that is done.

I also realized that I should probably change out the actual reefing line. It's an old frayed line, I"ll bet I would get much better results with a new slippery (so to speak) line.


I got a small block that included a shackle attached, and a stainless steel ring (about 2" diameter). Ring goes on the starboard side of the cringle, block on the port side with shackle reaching through around the ring. When you do this, the reefing line goes up and down on the port side instead of going through the cringle.

This isn't my boat or my picture, but this is how it looks on a former member's boat:

doublereefed Posted - 09/17/2019 : 12:50:02
Thanks for that Take Five. Hadn't though about the line needing to go to the end of the boom. I will figure that out.

How is the block attached to the cringle? I Googled and couldn't find any photos to show me how that is done.

I also realized that I should probably change out the actual reefing line. It's an old frayed line, I"ll bet I would get much better results with a new slippery (so to speak) line.

TakeFive Posted - 09/16/2019 : 15:58:24
Reef line needs to go back to end of the boom for appropriate foot tension (you want a flat sail in heavy weather).

A block in the clew cringles for each reef would greatly reduce the friction in a single line system. With that modification, I was always happy with single line reefing.

Adding a block at the tack always caused problems for me, because it would pull the sail below the boom before I had enough tension on the clew.

Association Forum © since 1999 Catalina Capri 25s International Association Go To Top Of Page
Powered By: Snitz Forums 2000 Version 3.4.06
Notice: The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.